Сброс параметров устройства в значения по умолчанию необходим в следующих случаях:
- утеря логина и/или пароля для доступа к web-интерфейсу устройства;
- отсутствие информации о текущем IP-адресе устройства;
- в некоторых случаях после выполнения процедуры обновления ПО устройства
Данная процедура приводит в значения по умолчанию все настраиваемые параметры устройства (IP-адрес, фильтры доступа, имя пользователя, пароль и другие настройки).
...
Resetting parameters of a device to default values is necessary in the next cases:
- login and/or password for accessing a web interface of a device is lost;
- no information about a current IP address of a device;
- in certain cases after updating firmware of a device
This procedure sets all customizable parameters of a device to default values (IP address, access filters, user name, password and other settings).
To reset parameters to default values, there is a need to consequently perform the next actions (for a NetPing 2/PWR-220 v3/ETH без встроенного аккумулятора device without a built-in battery):
- выключите питание устройства;
- нажмите кнопку сброса параметров «Reset»;
- включите питание устройства, продолжая удерживать кнопку «Reset» нажатой в течение 15-20 секунд;
- отпустите кнопку, все параметры устройства сброшены в значения по умолчанию
...
- switch off power of a device;
- press the reset button «Reset»;
- switch on power of a device keeping the «Reset» button pressed for 15-20 seconds;
- release the button, all parameters of a device are reset to default values
To reset parameters to default values, there is a need to consequently perform the next actions (for a NetPing 2/PWR-220 v2/SMS со встроенным аккумулятором device with a built-in battery):
- нажмите и удерживайте кнопку сброса параметров «Reset» более 5 секунд (используйте ручку/стилус/карандаш и т.п.);
- отпустите кнопку сброса параметров «Reset», светодиоды CPU у портов Ethernet замигают, все параметры устройства сброшены в значения по умолчанию
...
- press and keep the «Reset» button pressed for more than 5 seconds (use a pen/stilys/pencil, etc.);
- release the «Reset» button, CPU LEDs near Ethernet ports will blink, all parameters of a device are reset to default values
Info |
---|
Short-term clicking the «Reset» button will reboot a device (for a NetPing 2/PWR-220 v2/SMS со встроенным аккумулятором device with a built-in battery). |
Info |
---|
По умолчанию в устройстве установлены следующие параметры: Имя пользователяOn default, a device has the next parameters: User name: visor ПарольPassword: ping IP адресaddress: 192.168.0.100 Маска подсетиSubnet mask: 255.255.255.0 Гейт Gate (шлюзgateway): не установлен is not set SNMPcommunity: SWITCH MAC -адресaddress: 00 a2 xx xx xx xx Здесь Here, xx xx xx xx соответствует серийному номеру устройства. Таким образом, все устройства после производства имеют уникальные MAC-адреса. |
...
corresponds to a serial number of a device. Therefore, all devices have unique MAC addresses after being manufactured. |
After resetting parameters to default values, there is a need to perform an initial configuration of a device – see more detailed description in the document «Firmware description». Где взять документ описания встроенного ПО?