[ENG] 11.7. [DKSF 70/71.5 IU] What SMS Notifications Can a Device Send?
The information in the section corresponds to a device UniPing server solution v3/SMS with a built-in GSM modem.
A maximum length of SMS notifications cannot exceed 70 Latin or Cyrillic characters.
Syntax of SMS Notifications
SMS notifications look as follows:
where:
np_name – is a name of a device for identification SMS notifications. It is specified at the page «SETUP» of a device web interface. If a name of a device is not set, then the name NETPING is used
q – is a sequential number of a message. The number is nonvolatile – it is not zeroed when a power supply is switched off. It is used to register missed (lost) messages
Information – is an informational part of SMS notifications
Informational Part of SMS Notifications
A notification about changing a status of an IO line:
where:
n – is a number of an IO line, 1..4
label – is a label of an IO line, which is set in the field «Memo» at the page «INPUT-OUTPUT» of a device web interface. If a label is not specified (empty), then it is not included into SMS.
transcript – is a description of a logic level of an IO line, which is set in the pop-up dialog of setting notifications from IO lines at the page «INPUT-OUTPUT» of a device web interface. If a description is not set (empty), then it is not included into SMS.
A notification about a failure of a temperature sensor (a sensor stopped responding during requesting):
where:
j – is a number of a temperature sensor, 1..8
label – is a label of a temperature sensor, it is set in the fields «Memo» at the page «TEMPERATURE SENSORS» of a device web interface. A label in a text of a notification is quoted. If a label is not set (empty), then it is not included into SMS
A notification about a normal status of a temperature within the thresholds of a specified range at the page «TEMPERATURE SENSORS» of a device web interface:
where:
t – is a current temperature, °C
j – is a number of a temperature sensor, 1..8
t1, t2 – are thresholds of a «normal range», deg.С
label – is a label of a temperature sensor, which is set in the fields «Memo» at the page «TEMPERTURE SENSORS» of a device web interface. A label is quoted in the text of a notification. If a label is not specified (empty), then it is not included into SMS.
A notification about a temperature left the threshold of a specified range:
where:
t – is a current temperature, °C
t1, t2 – are thresholds of a «normal range» of a temperature, °C
j – is a number of a temperature range, 1..8
label – is a label of a temperature sensor, which is set in the fields «Memo» at the page «TEMPERATURE SENSORS» of a device web interface. A label is quoted in the text of a notification. If a label is not specified (empty), then it is not included into SMS
A notification about a failure of a humidity sensor (a sensor stopped responding when requesting):
where:
n – is a humidity sensor number, 1..4
label – is a label of a humidity sensor, which is set in the fields «Memo» at the page «HUMIDITY SENSORS» of a device web interface. A label is quoted in the text of a notification. If a label is not specified (empty), then it is not included into SMS
A notification about restoring an operability of a humidity sensor (a sensor started to respond when requesting):
where:
n – is a humidity sensor number, 1..4
h – is a relative humidity, %
t – is a current temperature, °C
label – is a humidity sensor label, which is set in the fields «Memo» at the page «HUMIDITY SENSORS» of a device web interface. A label is quoted in a text of a notification. If a label is not specified (empty), then it is not included into SMS
A notification about readings of a humidity sensor decreased a specified range:
where:
n – is a number of a humidity sensor, 1..4
h – is a relative humidity, %
h1, h2 – are the thresholds of a «normal range» of a relative humidity, %
label – is a humidity sensor label, which is set in the fields «Memo» at the page «HUMIDITY SENSORS» of a device web interface. A label is quoted in a text of a notification. If a label is not specified (empty), then it is not included into SMS
A notification about readings of a relative humidity returned to the specified safe range:
where:
n – is a number of a humidity sensor, 1..4
h – is a relative humidity, %
h1, h2 – are thresholds of a «normal range» of a relative humidity, %
label – is a humidity sensor label, which is set in the fields «Memo» at the page «HUMIDITY SENSORS» of a device web interface. A label is quoted in a text of a notification. If a label is not specified (empty), then it is not included into SMS
A notification about readings of a relative humidity increased a specified range:
where:
n – is a number of a humidity sensor, 1..4
h – is a relative humidity, %
h1, h2 – are thresholds of a «normal range» of a relative humidity, %
label – is a humidity sensor label, which is set in the fields «Memo» at the page «HUMIDITY SENSORS» of a device web interface. A label is quoted in a text of a notification. If a label is not specified (empty), then it is not included into SMS
A notification about temperature readings falling below a specified range (a temperature sensor is built inro a relative humidity sensor):
where:
n – is a number of a humidity sensor, 1..4
t - is a current temperature, °C
t1, t2 – are thresholds of a «normal» range of a temperature, °C
label – is a humidity sensor label, which is set in the fields «Memo» at the page «HUMIDITY SENSORS» of a device web interface. A label is quoted in a text of a notification. If a label is not specified (empty), then it is not included into SMS
A notification about temperature readings coming back to normal specified range (a temperature sensor is built into a relative humidity sensor):
where:
n – is a humidity sensor number, 1..4
t – is a current temperature, °C
t1, t2 – are thresholds of «normal» safe range of a temperature, °C
label – is a humidity sensor label, which is set in the fields «Memo» at the page «HUMIDITY SENSORS» of a device web interface. A label is quoted in a text of a notification. If a label is not specified (empty), then it is not included into SMS
A notification about temperature readings exceeding a specified range (a temperature sensor is built into a relative humidity sensor):
where:
n – is a humidity sensor number, 1..4
t – is a current temperature, °C
t1, t2 – are thresholds of a «normal» range of a temperature, °C
label – is a humidity sensor label, which is set in the fields «Memo» at the page «HUMIDITY SENSORS» of a device web interface. A label is quoted in a text of a notification. If a label is not specified (empty), then it is not included into SMS
A notification about switching an analogue smoke sensor to a normal status:
A notification about switching an analogue smoke sensor into a switched off status (power is disabled):
A notification about switching an analogue smoke sensor into a status «Alarm»:
A notification about switching an analogue smoke sensor to a status «Open Loop»:
A notification about switching an analogue smoke sensor into a status «Short Circuit»:
A notification about switching on/off a built-in relay:
where:
n – is a relay number
label – is a relay label, which is set in the field «Memo» at the page «Relay Management» of a device web interface. A label is quoted in the text of a message. If a label is not specified (empty), then it is not included into SMS
A notification about triggering the module «Watchdog» (a socket is switched off for a short time to restore the operation of a connected device):
where:
n – is a relay number
label – is a relay label, which is set in the field «Memo» at the page «RELAY MANAGEMENT» of a device web interface. A label is quoted in the text of a message. If a label is not set (empty), then it is not included into SMS
A notification about restoring and losing a connection with a specified address («PINGER» module):
where:
IP/HOST – is an address of a checked IP address/host
Periodic SMS Reports about a Status of Sensors, IO Lines and Relays
A feature of sending a daily report as SMS notification about a status of sensors, IO lines and relays is implemented in a device. You can read more detailed information about configuring this report in the section «11.9. [DKSF 70/71.5 IU] Configuring Time of Sending a Daily Report about a Status of Sensors, IO Lines and Relays in SMS Notifications».