[ENG] 8.7. [DKSF 52/202.10 IU] What SMS Notifications Can a Device Send?
Information in the section applies to the device NetPing 2/PWR-220 v2/SMS with a built-in GSM modem.
Syntax of SMS Notifications
SMS notification looks like the following:
where:
np_name – is a name of a device for the identification of SMS notifications. It is specified on the page «SETUP» of a device web interface. If a name of a device is not specified, then the name NETPING is used
q – is a consequent number of notifications. The number is non-volatile – it is not zeroed when the power is switched off. It is used for the registration of missed (lost) notifications
Information – is the informational part of SMS notifications
Informational Part of SMS Notifications
A notification about changing a status of an IO line:
where:
n – is a number of an IO line, 1..4
label – is a label of an IO line that is set in the field «Memo» on the page «DISCRETE IO» of a device web interface. If a label is not set (empty), then it is not included into SMS.
transcript – is a description of a logic level of an IO line, which is specified in the pop-up dialogue for the configuring notifications from IO line on the page «DISCRETE IO» of a device web interface. If a description is not set (empty), then it is not included into SMS.
A notificаtion about the failure of a temperature sensor (a sensor stopped responding while polling):
where:
n – is a number of a temperature sensor, 1..8
label – is a label of a temperature sensor, which is set in the field «Memo» on the page «TEMPERATURE» of a device web interface. A label in the text of a notification is quoted. If a label is not set (empty), then it is not included into SMS
A notification about a normal status of temperature within the specified range on the page «TEMPERATURE» of a device web interface:
where:
t – is a current temperature, °C
n – is a number of a temperature sensor, 1..8
t1, t2 – are the thresholds of the «normal» temperature range, °C
label – is a label of a temperature sensor, which is set in the field «Memo» on the page «TEMPERATURE» of a device web interface. A label is quoted in the text of a notification. If a label is not set (empty), it is not included into SMS.
A notification about the temperature leaving the threshold of the specified range:
where:
t – is a current temperature, °C
t1, t2 – are the thresholds of the «normal» temperature range, °C
n – a number of a temperature sensor, 1..8
label – is a label of a temperature sensor, which is set in the field «Memo» on the page «TEMPERATURE» of a device web interface. A label is quoted in the text of a notification. If a label is not set (empty), it is not included into SMS.
A notification about the failure of a humidity sensor (a sensor stopped responding while polling):
A notification about the readings of a humidity sensor return to the thresholds of the specified range:
where:
h – is a relative humidity, %
h1, h2 – are the thresholds of a «normal» relative humidity range, %
A notification about the readings of a relative humidity rising above the thresholds of the specified range of a relative humidity:
where:
h – is a relative humidity, %
h1, h2 – are the thresholds of the «normal» range of a relative humidity, %
A notification about falling of readings of the relative humidity below the specified range:
where:
h – is a relative humidity, %
h1, h2 – are the thresholds of a «normal» relative humidity range, %
Notification about switching on/off a built-in relay:
where:
n – is a relay number, 1..2
label – is a label of a temperature sensor, which is set in the field «Memo» on the page «TEMPERATURE» of a device web interface. A label is quoted in the text of a notification. If a label is not set (empty), it is not included into SMS.
A notification about triggering the module «Watchdog» (a socket is switched off for short time to restore the operation of a device connected to it):
where:
n – is a relay number, 1..2
label – is a label of a temperature sensor, which is set in the field «Memo» on the page «TEMPERATURE» of a device web interface. A label is quoted in the text of a notification. If a label is not set (empty), it is not included into SMS.
A notification about changing a status of a status of the Ethernet ports of a device:
A device has a built-in three-port switch with two external ports and one internal port, to which the CPU is connected.
A notification about restoring and losing a сonnection with a specified IP address (the module «Pinger»):
where:
n – is a number of the channel of the module «Pinger», 1..2
IP/HOST – is an address of the tested IP address/ DNS name
A notification about the switching of a device to the backup power from a battery (for the device NetPing 2/PWR-220 v2/SMS with a built-in battery):
A notification about a device switching to the main power from the 220 V electricity grid (for the device NetPing 2/PWR-220 v2/SMS with a built-in battery):
A notification about a low battery charge (for the device NetPing 2/PWR-220 v2/SMS with a built-in battery):
Periodic SMS Reports about a Status of Sensors, IO Lines and Relays
A feature of sending a daily report as SMS notifications about a status of sensors, IO lines, and relays, is implemented in a device. More detailed information about configuring this report can be ready in the section «[ENG] 8.9. [DKSF 52/202.10 IU] Setting the Time of Sending a Daily Report about a Status of Sensors, IO Lines and Relays as SMS Notification».