| Info |
|---|
The page has photos of a NetPing 2/PWR-220 v2/SMS device in the text. |
...
To prepare a device for operation, do the next: | ||||||||
1. Take a device out of the box and install on a horizontal surface.
|
| |||||||
2. Plug a GSM antenna to a device and locate it in the place of a reliable reception of the cell operator's signal (for a NetPing 2/PWR-220 v2/SMS device with a built-in GSM modem). The availability of a signal can be controlled using a cell phone according to the number of segments in the power indicator on a display of the phone. |
| |||||||
3. Insert a SIM card until the click in a corresponding jack on a front panel of a device (for a NetPing 2/PWR-220 v2/SMS device with a built-n GSM modem). Please, pay attention so that a SIM card is turned contacts up.
|
| |||||||
4. Plug the equipment, power of which must be controlled, to «PWR» sockets on a back panel of a device. To make a connection convenient, use the «monitor – system unit» cords or an adapter to connect PWR-220. Cords and adapters are not included into a shipping kit and can be purchased separately if necessary. |
| |||||||
5. Connect Plug external sensors to a device (see the details in the section «Подключение внешних датчиковPlugging External Sensors») и/или нагрузкуand/or a load.
| ||||||||
6. Подключите устройство к сети питанияPlug a device to a power supply network.
|
| |||||||
Индикатором наличия питания будет свечение светодиодов CPU у портов Ethernet на лицевой панели устройства.
В процессе инициализации устройства светодиоды несколько раз замигают, указывая на включение устройства, после этого будут светиться постоянно. | ||||||||
7. Подсоедините устройство к офисной сети Ethernet в любой свободный порт Ethernet коммутатора. |
| |||||||
Свечение светодиода link у соответствующего порта Ethernet на лицевой панели устройства будет означать, что соединение установлено успешно.
Второй Ethernet порт можно использовать для подключения любых Ethernet-устройств, в том числе и других устройств NetPing, «цепочкой». | ||||||||
| Info |
|---|
Только что купленное устройство или устройство, для которого была выполнена процедура сброса параметров в значения по умолчанию (см. «Сброс параметров в значения по умолчанию»), требует первоначальной настройки сетевых адресов и параметров управления нагрузками. После этого устройство может быть установлено в существующую сеть. Его дальнейшее конфигурирование можно будет выполнить, используя удалённый доступ к устройству. О настройке подробнее см. в документе «Описание встроенного ПО». Где взять документ описания встроенного ПО? |
Important! A device is designed to be connected to a power supply network with the voltage of 110V - 220V and a frequency of 50/60 Hz. Do not plug a device to power supply networks with other parameters! |
Glowing of CPU LEDs near Ethernet ports on a front panel of a device will be an indicator of power supply.
In the process of a device initialiation, LEDs blink several times indicating switching on of a device, and then will be glowing constantly.
7. Connect a device to the office Ethernet network to any free Ethernet port of a switch.
Glowing of a link LED near a corresponding Ethernet port on a front panel of a device will mean that a connection is successfully established.
The second Ethernet port may be used to plug any Ethernet devices including other NetPing devices, in a «chain».
A device is connected and ready to work.
| Info |
|---|
A device that has been purchased right now or a device for which a procedure of resetting parameters to default values has been performed (see «Resetting Parameters to Default Values»), requires the initial configuration of network addresses and parameters of load control. After this, a device can be installed into an existing network. Its further configuration may be performed by using a remote access to a device. More detailed information about a configuration can be found in the document «Firmware description». Where to Get a Document with a Firmware Description? |
| Warning |
|---|
Important! It is not recommended to connect real network and computer equipment to power sockets at the first switching on and familiarizing with the operation logic of a device. Frequent cycles of switching on/off may cause equipment failure. During the time of familiarizing with a device, it is possible to conect an indifferent load (for example, a table lamp) to power sockets or track a power supply status on power sockets by glowing of corresponding LEDs. |